A UE error code on your LG front-load washer means the washer won't spin because the load is unbalanced. Show Fixing an LG washing machine UE code can be as easy as redistributing an unbalanced load or adding a few garments to a small or single-item load. Balance the loadTry the following solutions to get your washer spinning again.
Level the legsIf the LG washing machine UE code appears when the load is balanced, check the leveling legs under the washer. All 4 leveling legs must be firmly on the floor to provide stability when the washer spins. Press down kitty corner on the top of the washer to check its stability. If the washer rocks even slightly, then the machine will vibrate during the spin cycle and trigger the LG front-load washer error code UE. Adjust a leveling leg by loosening the lock nut holding the leg in place and rotating the leg clockwise to lower it or counterclockwise to raise it. You may only need to adjust one leveling leg to eliminate rocking. Tighten the lock nut firmly after adjusting the leveling leg. A washer that’s not level also can vibrate and trigger the UE error code. After you adjust the leveling legs to make the washer stable, place a bubble level on the top of the washer and check for levelness front-to-back and side-to-side. If levelness is off by a quarter bubble or less, you don’t need to do anything. If levelness is off by more than a quarter bubble, adjust the legs. Check for a broken partThese tips will help you resolve most problems that cause the UE error code on an LG front-load washer. If you're still seeing the code after following these tips, then a damper shock or suspension spring could be broken. Unplug the washer and remove the top panel to check those parts. Replace the broken part, or have a service technician replace the part if you're not confident that you can complete the repair yourself.
An LG Washer with a UE error code indicates that the washing load is unbalanced. If you are lucky, the washer will fix the error itself by filling it with more water to help agitate and separate the items in the washer. At this stage of the process, most LG washers will display a lowercase “u” (uE) error code. If the washer is unable to balance the load, the washer will display a UE error code. If the washer cannot balance the load, the first step is to try to balance it yourself. Failing that, you should check that the washer is sitting level on the floor. If the issue persists, you may have a more serious problem and will need to check the rotor mounting nut, suspension rods, shock absorbers, hall sensor, and control board. A washer reset may also resolve the error code if the error is just a glitch. This guide applies to most LG washers, including the following models: RLM20K WD-10271BD WD-11275BD WD-13276BDM WD-90282BD WM2233HW WM2277HS WM2301HR WM2301HW WM2455HG WM2455HW WM2455HW/00 WM2487HRMA/00 WM2487HWMA/00 WM2496HSM WM2496HWM/00 WM2688HNM WM2688HWMA/00 WM3070HWA WM3470HVA WM3470HWA 1. Balance the LoadThe easiest solution to the problem is to open the washer and adjust the load. If the laundry is tangled, bunched up, or stuck to one side, correcting this will often resolve the issue. Overloading or underloading can also cause the error, so another easy solution is to either remove or add an item or two to the load to balance it out. Items with strings or laces can also cause the error if they get caught in a part of the drum or agitator. To ensure this doesn’t happen, use a washing machine-safe bag or secure the strings so that they cannot get caught in the washer. It is also important to ensure you use the correct cycle when using the washer. Each wash cycle is designed to wash specific fabric types and soil levels. If the washer is expecting a different type of load, it may think that the washer is unbalanced and display the UE error code. Once the weight of load has been rebalanced, the error code should be resolved, and the washer should continue with the cycle. 2. Level the WasherAnother cause of the UE error code is that the washer is not sitting level on the floor. Using a level tool is the best way to check and fix the issue. If the level tool shows you the washer is not level, the washer’s legs should be adjusted until the washer is level. To adjust the leveling legs, locate the locking nut on the leg and loosen it with a wrench. Adjust the legs until the washer is level. When you have verified that the washer is level, tighten the locking nuts to lock them into place. 3. Reset the WasherOccasionally, the error code may occur because of a glitch with the control board. If there is a glitch, disconnecting the washer from the power for five minutes will allow the control board to reset. If it is just a glitch, the error code should be gone when you reconnect the power to the washer. However, resetting the washer like this may also just postpone the inevitable. If the error code returns, it is important to take the time to fix the issue, as putting it off will likely lead to more serious issues in the future. 4. Check the Rotor Mounting NutIf the above steps have failed to resolve the error, you will need to check some of the internal components responsible for balancing the tub in the washer. These repairs can be complicated and are best performed by a trained professional. However, if you are feeling confident, the first thing to check is the rotor mounting nut. The purpose of the rotor mounting nut is to help secure the rotor assembly over the stator. Follow these instructions to check the rotor mounting nut:
5. Check the Suspension Rods (Top-Loader Washers)Top-loader washers have suspension rods that, over time, can wear out. If the suspension rods need to be replaced, the washer will vibrate excessively, make a lot of noise, and trigger the UE error code. Follow these steps to check the suspension rods:
6. Check the Shock Absorbers (Front-Loader Washers)If you have a front-loader washer, the shock absorbers that help secure the tub may have worn out. If the shock absorbers are defective, the washer will vibrate excessively, make noise, and trigger a UE error code. Follow these steps to check the shock absorbers:
7. Check the Hall SensorThe hall sensor (also called the rotor position sensor) monitors how the motor is operating. When it becomes defective, it can cause error codes to be displayed when they shouldn’t be. Follow these steps to check the hall sensor:
8. Replace the Control BoardThe washer’s control board sends and receives electronic signals to operate the washer. If the above solutions have failed to fix the UE error code, the washer may have a faulty control board. Testing and replacing the control board can be difficult; therefore, it is best left to a trained professional. If the control board is faulty, it will need to be replaced. |